< Path: ukma!rutgers!super.upenn.edu!eecae!nancy!umix!uunet!seismo!rick < >From: rick@seismo.CSS.GOV (Rick Adams) < Newsgroups: comp.dcom.modems,news.config < Subject: Telebit Modem Hints (telebit is down) < Message-ID: <44175@beno.seismo.CSS.GOV> < Date: 2 Nov 87 23:02:35 GMT < Organization: Center for Seismic Studies, Arlington, VA < Lines: 120 < < The uucp site "telebit" is down with a dead hard disk. They hope to < be back up soon. < < Those of you who have received telebit modems without detailed instructions < on how to configure them for uucp may find the following information useful. < < Telebit will be publishing an "official" how to configure guide soon, but the < guide was on the hard disk that was trashed... < < The following information works for 4.3bsd, 4.2bsd and HoneyDanBer. I'm not < sure if the "old" System V.2 uucp supports chat scripts in L-devices. < < Basically, you use the stock Hayes dialer with a small change to the < chat script. This is presented as an "it works for me" help file as < opposed to anything formal. < < ---rick < < [most of this information comes from other people including < John Gilmore and Peter Honeyman] < < Devices and Systems are honey danber, L-devices is bsd. a Systems or < L.sys entry is `vanilla': < < host Any ACU speed phone etc. < < Devices: < < ACU tty11 - 1200 tb1200 < ACU tty11 - 2400 tb2400 < ACU tty11 - 9600 tbfast < ACU tty11 - 19200 tbfast < < Dialers: < < tb1200 =W-, "" A\pA\pA\pT OK ATS50=2DT\T CONNECT\s1200 < tb2400 =W-, "" A\pA\pA\pT OK ATS50=3DT\T CONNECT\s2400 < tbfast =W-, "" A\pA\pA\pT OK ATS50=255DT\T CONNECT\sFAST < < L-devices: < < ACU ttyd1 unused 1200 hayestone "" A\dA\dA\dT OK ATS50=2X0 OK < ACU ttyd1 unused 2400 hayestone "" A\dA\dA\dT OK ATS50=3X0 OK < ACU ttyd1 unused 9600 hayestone "" A\dA\dA\dT OK ATS50=255X0 OK < ACU ttyd1 unused 19200 hayestone "" A\dA\dA\dT OK ATS50=255X0 OK < < S registers: < < < [ uunet is the uunet machine, a Sequent balance 21k Dynix 2.1 ] < [ cfcl is Rich Morin's " machine, a Sun 2 running Sun 3.3 ] < [ Hoptoad is John Gilmore's machine, a Sun 3 running Sun 3.4 ] < [ Honey is Peter Honeymans machine, a 3BX (?) running system 5 with HDB ] < < factory Uunet cfcl Hoptoad Honey < < E1 E1 E1 E1 E1 Echo ON/OFF < F1 F1 F1 F1 F1 Echoplex ON/OFF < M1 M1 M1 M1 M2 Speaker ON/OFF < Q0 Q6 Q0 Q0 Q6 Quiet Enable < T T T T T Tone Dialing < V1 V1 V1 V1 V1 Verbose ON/OFF < X1 X1 X1 X0 X1 Result Code Basic/Extended < < S00 001 001 001 001 001 Answer on Ring Number < S01 000 000 000 000 000 Count of Rings < S02 043 043 043 043 043 Escape Character < S03 013 013 013 013 013 Carriage Return Character < S04 010 010 010 010 010 Line Feed Character < S05 008 008 008 008 008 Backspace Character < S06 002 002 002 002 002 Dial Tone Wait Time < S07 040 040 040 040 040 Wait for Carrier Time < S08 002 002 002 002 002 Pause Time for Comma < S09 006 006 006 006 006 Carrier Detect Time < < S10 007 007 007 007 007 Carrier Loss to Reconnect Time < S11 070 070 070 050 070 Touch Tone Timing < S12 050 050 050 050 050 Escape Sequence Guard Time < < S45 000 255 000 255 255 Remote Access Enable < S47 004 004 004 004 004 DSR Delay time < S48 000 000 000 000 000 Eight Bit Comparison < S49 000 000 000 000 000 Product Ident. String Redef. < < S50 000 000 000 000 000 Transmission Mode < S51 004 254 255 005 255 Interface Speed < S52 000 002 002 002 002 DTR Interpretation < S53 000 004 001 001 000 DCD & DSR Interpretation < S54 000 003 003 003 003 Break Signal Interpretation < S55 000 000 000 000 000 Escape Char./Seq. Interp. < S56 017 017 017 017 017 XON Character < S57 019 019 019 019 019 XOFF Character < S58 003 003 000 000 000 Flow Control used by DTE < S59 000 000 000 000 000 Prompt Character < < S60 000 000 000 000 000 Data Format < S61 045 045 010 000 255 Speaker Volume < S62 003 003 003 003 003 Break Length Time < S63 001 001 001 001 001 Attention Code ON/OFF < S64 000 000 000 000 000 Dial/Answer Sequence Abort < S65 000 000 000 000 000 XON/XOFF Failsafe < S66 000 000 000 000 000 Lock Interface Speed < S67 000 000 000 000 000 CTS Interpretation < S68 255 255 255 255 255 Flow Control used by DCE < < S90 000 000 000 000 000 V.22 Emulation Mode Enable < S91 000 000 000 000 000 Guard Tone Selection < S92 000 001 000 001 000 PEP tones after 2400/1200/300 < S95 000 000 000 000 000 MNP Operating Mode < < S100 000 000 000 000 000 Reverse Answer/Originate Mode < S101 000 000 000 000 000 Continuous Answer/Originate < S102 000 000 000 000 000 Auxiliary Telco Lead Setting < S104 000 000 000 000 000 Automatic dialing < < S110 255 001 255 255 255 Data Compression Enable < S111 255 030 030 030 030 Asynchronous Protocols Support < S112 001 001 001 001 001 Kermit Mark Character < < S121 000 000 000 000 000 Echo Suppressor Compensation <